How To Install A Headset On A Mountain Bike

How To: Installing A Headset

In this MTB How To, we are going to be installing a new headset! Whenever yous are replacing the headset on your mountain bike, it is very of import to align the headset cups and bearings properly and use grease in only the right places. Here nosotros are going to be walking you through step past step to ensure you get the most life out of your headset. No i likes a creaky headset!

Here we volition be installing a Pikestaff Creek 110 serial headset on to a Santa Cruz V10. All of Cane Creek's 110 serial models are designed, machined, assembled, and tested correct in Fletcher, North Carolina. American Made! The specific model headset used is a Cane Creek 110 ZS49/28.six / ZS49/30.

What Tools Exercise Nosotros Need?

Before we start, allow's become over what tools will be necessary to become the job done simply right. In gild to go a perfect install, we will be using a Park Besides HHP-2 Headset Printing. Nosotros would not recommend using a rubber mallet every bit an alternative simply will say it tin exist done. Next we have a Park Tool Crown Race Setting Arrangement and Park Tool mallet to install crown race safely. For grease, nosotros like to use Maxima's waterproof grease. Lastly, you will need a good set of allen keys. Thanks to the guys at Old Spokes Home bike shop in Burlington, Vermont for letting u.s. employ the tools for this MTB How To.

1. Install Crown Race

• Kickoff we are going to start off installing the crown race on to the steerer tube. The crown race is what meshes the steerer tube and the bottom bearing of the headset. It is important to make certain the race gets pressed all the mode down onto the crown. The crown shown below is for a Play tricks xl fork and that is why the fork has been removed from the crown. The aforementioned technique can exist practical to a single crown fork.
• Utilise a thin film of grease onto the inner ring of the race so that it slides in to identify with ease.  It is also smart to apply minimal grease on the safe gasket on top of the race to prevent from it from being damaged while being installed. Using the Park Tool mallet, hit the top of the Park Tool Crown Race Setting Tool until the race is affluent with the top of the crown.

2. Make Certain The Head Tube and Headset Are Clean

• Audit the condition of the head tube on your bike. Use whatever type of rag or shop towel to clean the inside of the headtube then that no droppings has a chance of getting to the headset from the inside.
• Also accept a quick glance at the headset before you install information technology. Double check tom ake sure you have the correct headset to fit your bike.

3. Grease The Top And Bottom Headset Cups

• The next stride is make sure everything is properly greased before pressing in the headset cups themselves. We like to utilize Maxima Waterproof Grease, and with whatever kind of applicator, apply a sparse layer of grease on both headset cups and the dust cap as shown below.
• On the grit cap specifically, information technology is easy to apply too much grease. When the headset is filled with as well much grease, some will make it out the side of the top cap and start to collect dirt when riding. The Maxima grease is great considering it likes to stick around fifty-fifty after washing your bike.

4. Printing In The Top Cup

• Now here it goes. It'due south fourth dimension to utilize the Park Tool HHP-2 Headset Press. We always recommend installing ane headset cup at a time. This makes it much easier to ensure the headset cups are each aligned properly. This is even more relevant for those installing an offset headset.
• Get-go place the top headset cup in to place and aligned correctly. Slide the Park Tool Headset Press in to place and slide the bottom neckband upward until it clicks in to position. Tighten the handle snug until the headset loving cup is flush with the top of the head tube. Make certain that as the headset loving cup is sliding in it remains straight.

5. Press In The Bottom Cup

• Repeat the same procedure described in a higher place and printing in the bottom headset cup. Again make certain that the loving cup is pressed in straight. Tighten the Park Tool Headset Press until things are snug and the headset is flush with the headtube. The orientation of the headset printing can remain the same while installing both the top and bottom headset cups.

half-dozen. Assemble Headset

• At present that the headset cups have been installed, it's time to assemble the rest of the headset. Start past applying a thin layer of grease on to each of the bearings and pushing those in to place. If you oasis't already, grease the dust cap and identify it on height of the headset. The 110 series headsets from Cane Creek also come with a golden lock ring. Exist certain to include the lock ring before installing any headset spacers.

seven. Insert Fork and Tighten Top Cap

• Almost at that place! Throw simply a touch of Maxima grease around the crown race and slide the steerer tube through the headset. Printing the dust cap downwardly onto the steerer tube to get a tight fit. The steerer tube here has already been cut to length and a star nut installed.
• Because the fork being used hither is a dual crown, the summit crown also acts like a stem spacer. Slide the top crown down on to the steerer tube. Place the appropriate spacers on to the steerer tube and then tighten the meridian cap. The spacers should come up to at least ane/4" above the top of the steerer tube for the headset to tighten properly. If the fork/handlebars are reluctant to turn dorsum and quaternary, the peak cap may be too tight. A snug fight, not overtightened, will extend the life of your headset bearings.

8. Get Ride Your Bike!

Max Morgan Racing in Colombia, South America for the Pan American Championships

Source: https://www.worldwidecyclery.com/blogs/worldwide-cyclery-blog/how-to-installing-a-headset

Posted by: sandersonguitterotice.blogspot.com

Share this post